Oil & Natural Gas Projects
Exploration and Production Technologies
Enhanced Oil Recovery by Horizontal Waterflooding
The overall objective of this project is to demonstrate that horizontal waterflooding can be technically and economically effective in the recovery of oil from the Bartlesville formation in the 100-year-old Wolco field, Osage County, Oklahoma. Drilling short-radius horizontal wells underbalanced will minimize formation damage, allowing for the cost-effective production of any remaining reserves in the abandoned Wolco field.
Grand Resources, Inc.
Three horizontal wells (one water injector straddled by two producers) were
drilled in a heel-to-toe configuration in Wolco field. Waterflooding this configuration
resulted in uneconomic, low oil recovery (8 barrels of oil per day) and high
water production (700 barrels of water per day).
Analysis of the pilot showed that the two horizontal producing wells were drilled into a zone with near-residual oil saturation. A spinner survey of the horizontal injector well indicated that water was entering the formation through a mere 15 foot heel section of the injection well. With the new information from the pilot, the two horizontal producing wells were re-drilled in the opposite direction and positioned 10 feet from the top of the formation where the oil saturation was higher. An existing well, located near the toes of the producers, was converted into a vertical injector with the injected fluid going into a high permeability zone lower in the formation.
Oil recovery increased to 15 barrels per day, while water production was slashed to 135 barrels per day, making this waterflood economic. It was concluded that abandoned fields can become economic if adequate oil saturations exist, along with an attractive combination of bottomhole pressure, permeability, and the proper placement of horizontal wellbores.
The primary benefit of this project is to prove the concept that horizontal
wells can be used to reestablish economic oil production in old fields that
are scheduled to be plugged and abandoned. The performance of the horizontal
injection well proved that large volumes of water can be injected below parting
pressure in the tighter reservoirs found in northeast Oklahoma. The results
will serve as a guide for other operators and allow them to reconsider the value
of poorly performing waterfloods in light of the low-cost horizontal technology
demonstrated by this project.
Oil fields in the Osage Nation are in a mature stage of depletion, yet millions of barrels of potentially recoverable bypassed oil remain in the Bartlesville sandstone, a shallow, low-permeability, naturally fractured reservoir. Conventional waterfloods using vertical wells in this formation are often unsuccessful because water cannot be injected below the reservoir parting pressure at a volume high enough to improve oil recovery. Channeling and poor oil recovery are typical if the fracture-parting pressure of the reservoir is exceeded. By using horizontal injection wells, large volumes of water can be injected below this parting pressure and a substantial amount of additional oil can be recovered. This project utilized horizontal wells and secondary recovery techniques to demonstrate that improved oil recovery could be achieved from an abandoned reservoir.
This three-year project tested horizontal waterflooding as a means of improving
oil recovery from the Middle Pennsylvanian Bartlesville Formation in Wolco field.
Three horizontal wells were drilled-an injector surrounded by two producer wells-arranged
in a heel-to-toe configuration to minimize heel-to-heel interaction between
the injection well and the horizontal producers.
The selection of Wolco field for the pilot location was based on cumulative
oil production, remaining recoverable reserves, reservoir characteristics, and
available infrastructure. Numerical simulations were conducted to determine
whether project economics were favorable.
Although Wolco field had never been waterflooded, the nearby North Avant Unit
had showed early water breakthrough from high water-injection rates that exceeded
the fracture parting pressure. This knowledge was used to design injection rates
below the fracture parting pressure.
The Bartlesville Formation was deposited in a fluvial incised valley and ranges
from braided fluvial deposits in the formation's lower zone to meandering fluvial
deposits in the upper portion of the reservoir. In the pilot area, the sandstone
is 80 feet thick, with an average permeability of 20 millidarcies and porosities
ranging from greater than 20% in the lower zone to 15-20% in the upper zone.
The formation is fractured, with surface fractures dominantly oriented N35E.
Simulation studies indicated that the horizontal injection wells be drilled
20 feet from the bottom of the sand, with the two producing wells 20 feet from
the top of the sand. The horizontal wells were drilled parallel to the suspected
prevailing fracture orientation within the field.
The wells were drilled with a curve-drilling assembly configured to drill a
70-foot radius curve. A lateral drilling assembly was used to drill the horizontal
section of the wells. The vertical part of the wells was drilled with air, the
short-radius curve with water, and the lateral section of the wells with air/foam
to minimize formation damage.
During water injection, water breakthrough was accompanied by disappointingly
low oil production-8 barrels per day-and high water production at 700 barrels
per day. A spinner survey run in the injection well indicated that all injected
fluids were entering the formation within only a 15-foot section of the well.
Well-log surveys on both producing wells suggested that the laterals were drilling
too deep and should be nearer the top of the formation, where oil saturation
Re-drilling the producing wells in the opposite direction closer to the top of the formation and converting an existing well located near the toes of the producers into a vertical injector increased oil production to 15 barrels per day, making the project economical.
Due to the success of the reconfiguration, other opportunities to apply the technology were considered. A series of workovers, cased-hole logs and bottom-hole pressure measurements were conducted on the adjacent lease to the east of the project area. The information gathered indicated the potential for recovering additional oil.
Wells #325 and 328, originally drilled and completed in 1914, were re-entered and drilled horizontally. They have responded favorably, with a combined production of approximately 40 BOPD and 600 BWPD. This is significant, considering the age of the wells and that this portion of the field has been shut in since the 1980s.
Current Status (June 2006)
The project results attracted the attention of the operator of an adjacent lease to the northeast, leading to a joint effort to plan and drill a horizontal producing well in an ongoing waterflood. Well #55 has not responded favorably to date. Good oil saturation was indicated on the logs; however, the well produces a large volume of water. The source has not yet been identified, although it is speculated that fracture communication with an injection well is the cause.
Three additional wells are being considered for reentry. New wells are being considered where old wells are unavailable. Current data indicates the potential for economic oil production.
The original contract was due to be completed by September 6, 2004; a no-cost
extension was requested and granted, putting the completion of the project at
September 6, 2005.
Project Start: September 6, 2002
Project End: September 5, 2005
Anticipated DOE Contribution: $399,640
Performer Contribution: $478,768 (55% of total)
NETL - Virginia Weyland (email@example.com or 918-699-2041)
Grand Resources - Scott Rabinowitz (firstname.lastname@example.org or 492-2366)
Semi-annual reports have been submitted to DOE through May 31, 2006.
Westermark, R.V.; Robinowitz, S.; Weyland, H.V.: “Horizontal Waterflooding Increases Injectivity and Accelerates Recovery”, World Oil V 225, No 3, pp 81-82, March 2004.
Westermark, R.V.; Dauben, D.; Robinowitz, S.: “Enhanced Oil Recovery with Horizontal Waterflooding, Osage County, Oklahoma”, SPE 89373, presented at the 2004 SPE/DOE Fourteenth Symposium on Improved Oil Recovery, Tulsa, OK, April 17-21, 2004.
Westermark, R. V.; Robinowitz, S.; Dauben, D.; Weyland, H.V.: “Horizontal Waterflooding Enhances Oil Recovery in Shallow, Low-Permeability Bartlesville Sandstone”, American Oil and Gas Reporter, September 2004
Westermark, R.V.; Schmeling, J.; Dauben, D.; Robinowitz, S.; Weyland H.V.: “Increased Production Results From Pilot Horizontal Waterflood in Osage County, Oklahoma”, SPE 94094, presented at the 2005 SPE Production and Operations Symposium, Oklahoma City, Oklahoma, April 17-19, 2005.
Osage County, OK, oil production well.